Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
Just about everyone has got their private piece of advice on the subject of How to Install a Bathtub Yourself.
Installing a bath tub isn't exactly rocket science, but it does need strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a moderately challenging task. If the old bathtub is readily available, the project can move immediately; if you need to open up a wall surface to eliminate the old bathtub as well as position the new tub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as embeded in the new one. See to it you have certified yourself for the task and are comfortable trying it. Instead of working with a service provider to take control of a halfway-completed project, it is better to take into consideration employing one before you start. Chances are you may require a specialist plumber to make tube links.
This article will assist you mount a new bath tub in your bathroom if you have actually already bought a new tub as well as don't need to change the setup of your previous water system pipes.
Your tools and product checklist need to make up the following:
Getting ready for the Installment
To start with, the supporting framework provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps device to stop strain on the bathtub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its last setting.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, then the first thing you should do is detach the water supply. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be quite troublesome because of the restricted access that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a fabric prepared for the staying water that will come from the pipes. When the supply pipelines have been removed, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Before going on to fit the new taps, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Tub
Making use of the two wood boards under its feet, put the bathtub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 little points.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level as well as adjusting the feet on the bath tub until the spirit level reviews level.
To mount taps, fit all-time low of the furthest versatile faucet port to the suitable supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply as well as check all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill the tub and likewise examine the overflow outlet and also the typical electrical outlet for leaks.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and also sealing around the tub must wait up until the tub has actually been used a minimum of when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making sure that the washers are in area between the faucet and the sink. Secure the faucet in position with the maker provided backnut. As soon as the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind should be connected to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to split a rigid seal, creating the water to pass through the wall surface between the bath and also the tiling, bring about problems with moisture as well as feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and can securing voids up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the bath tub with water before securing, to permit the activity experienced when the bathtub remains in usage. The sealer can crack relatively early if you do not think about this activity before securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily available on the market. It is advisable to fit the ceramic tiles using water-resistant or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very interested in Installing A Bathtub and I am praying you enjoyed the new entry. Loved our article? Please share it. Let other people check it out. Kudos for your time. Don't forget to check up our website back soon.
No more waits! Report this page